PERBOND
← The Journal
· The PerBond Team

How Much Epoxy Do You Need for a Bonded Repair? From Glue Line to Weighed Batch

Epoxy is the one common adhesive where guessing the quantity costs you twice. Mix too little and you are measuring a second batch while the first one gels on the job. Mix too much and the surplus heats itself up in the cup, shortens your working time and goes in the bin. This guide gets from the size of a bond to a weighed batch in two steps: the Adhesive Coverage Calculator for how much, and the Epoxy Mix Ratio Calculator for how to split it.

Step 1: area times glue-line thickness

The adhesive in a bond is a very thin slab: its area multiplied by the thickness of the glue line. The example for this guide is two panels 600 mm by 300 mm laminated face to face, a bond area of 1,800 cm². The only judgement is the thickness, and it changes the answer in direct proportion:

Glue lineVolumeMass at 1.1 g/mlTypical of
0.1 mm18 ml19.8 gFlat, machined surfaces under firm clamping
0.2 mm36 ml39.6 gWell-fitted parts, light clamping
0.3 mm54 ml59.4 gSanded sheet materials, hand pressure or weights
0.5 mm90 ml99 gSlightly uneven or rough-sawn surfaces
1.0 mm180 ml198 gA deliberate gap-filling joint with thickened epoxy

Going from a 0.1 mm line to a 1 mm line is ten times the epoxy on the same two panels. If your product's technical data sheet recommends a bond-line thickness, use it; many structural epoxies are strongest somewhere in the 0.1 to 0.5 mm range and some include glass beads to hold the gap open. For the example we will take 0.3 mm: 54 ml, or 59.4 g.

Step 2: add an allowance and round to something you can weigh

The calculator's figure is the epoxy that ends up in the joint. You also need the epoxy that coats the cup and the stirrer, wets the roller or spreader, and squeezes out at the edges. A quarter on top is a reasonable start for a job of this size, rounded up to the next 5 g so the weights are easy to hit. Twenty-five percent on 59.4 g, rounded up, is a 75 g batch.

Small jobs need a proportionally bigger allowance, because the film on the cup wall does not shrink with the batch. A bracket 150 mm by 80 mm (120 cm²) at 0.2 mm needs only 2.4 ml, 2.64 g, in the joint. Nobody can mix that amount accurately, which leads to the next point.

Step 3: check the batch is big enough to weigh accurately

Take a 20 g batch of an epoxy with a 100:30 mix ratio by weight. The mix calculator splits it into 15.38 g of resin and 4.62 g of hardener. A kitchen scale that reads to the nearest gram can be half a gram out either way, and half a gram on 4.62 g is an error of 11 percent in the hardener. That is enough to leave some epoxies soft. On a scale that reads to 0.1 g the same uncertainty is about 1.1 percent.

So there are two ways to mix a small quantity properly: use a 0.1 g scale, or mix a larger batch than the joint needs and accept the waste. For anything under about 20 g, a dual-cartridge syringe or a cartridge with a static mixing nozzle is usually the better tool, because it meters the ratio for you.

Step 4: split the batch

Our 75 g batch, in an epoxy whose data sheet gives 100:45 by weight, goes into the Epoxy Mix Ratio Calculator as ratio 100 to 45, total 75, basis "Weight". It returns:

  • Part A (resin): 51.72 g
  • Part B (hardener): 23.28 g

Weigh the resin first, tare the scale, then add hardener up to its figure. If you overshoot the hardener, do not scoop it back out; add resin to bring the batch back on ratio: raise the total in the calculator until its Part B figure matches what is in the cup, then top the resin up to the new Part A figure. Then mix for the time the data sheet states, scraping the sides and the bottom of the cup, because unmixed material on the cup wall is the commonest cause of sticky patches. The ratio and the basis (weight or volume) always come from the data sheet for your product: weight and volume ratios are not interchangeable.

Step 5: check the batch against the exotherm warning

Epoxy gives off heat as it cures, and a deep mass in a cup holds that heat in, which speeds the reaction, which makes more heat. The mix calculator flags any batch over 100 g for this reason. Our 75 g batch is under it (flagged: no). If you decided to laminate two such pairs of panels in one session and mixed 150 g in one cup, the warning would show (flagged: yes). The better plan is two batches of 75 g, mixed one after the other, or one batch tipped straight into a wide, shallow tray so the heat can escape. Pot life and batch size has the detail.

Variations on the same method

Thickened or filled epoxy

Epoxy thickened with filler, or a pre-filled paste, is denser than clear resin. Enter the density from the data sheet. At 1.5 g/ml the 0.3 mm example weighs 81 g, not 59.4 g, for the same volume. If you are buying by weight, that difference decides whether one pack is enough.

A fillet or a bead

For a bead of thickened epoxy, switch the coverage calculator to "Round bead diameter + length". A 6 mm bead round the 1.8 m perimeter of one of the panels is 50.9 ml, about 56 g at the default density. That is close to the amount in the whole face bond, which is why edge fillets should be counted, not treated as a rounding error.

Porous materials

Wood, concrete and foam absorb unthickened epoxy. The usual practice is a thin priming coat of mixed resin first, then the bonding coat, and the priming coat is extra to everything above. The calculator has no input for absorption; a test on an offcut is the only reliable guide.

What the calculators do not cover

  • Neither calculator adds an allowance for waste. The 25 percent used here is a starting point, not a rule.
  • The coverage calculator assumes an even glue line. A warped panel with a 2 mm hollow in the middle takes far more than the nominal figure.
  • The default density of 1.1 g/ml is typical of unfilled two-part epoxy. Yours may differ.
  • The mix calculator splits a total exactly; it cannot know your product's ratio, tolerance or mixing time.
  • Nothing here says whether the repair will be strong enough. Quantity and strength are separate questions.

Safety and limits

Epoxy resins and hardeners are skin sensitisers. Repeated skin contact can cause an allergy that is permanent, after which even small exposures bring out a rash. Wear nitrile gloves, change them when they are contaminated, cover your forearms and wear eye protection: many hardeners are corrosive and a splash in the eye is an emergency. Wash skin with soap and water or a hand cleaner made for resins. Never use solvent on skin, because it carries the resin through it. Work with good ventilation, and do not sand epoxy until it has fully cured, since dust from part-cured epoxy is itself sensitising.

A mixed batch gets hot. Large batches left in a cup can smoke, melt the container and give off irritating fumes. Mix only what you can use, and stand leftover mixed epoxy somewhere it can cool safely, outside if possible, until it has hardened.

Read the product's Safety Data Sheet (SDS) and technical data sheet before you start. The manufacturer's mix ratio, pot life and cure schedule override any figure in this guide. A bonded repair to anything load-bearing, overhead, on a vehicle or a boat's structure, or where a failure could hurt someone, needs the manufacturer's repair procedure and a qualified engineer or surveyor, not a quantity estimate.

The method in five lines

  1. Bond area × glue-line thickness gives the volume; the calculator converts it to grams.
  2. Add about a quarter for the cup, the tools and squeeze-out, more on small jobs.
  3. Make sure the smaller component is heavy enough for your scale to weigh to within a few percent.
  4. Split the batch at the data sheet's ratio, on the data sheet's basis.
  5. Keep each batch at or under 100 g, or spread it out, and time the job with the Cure Time Calculator if the workshop is cold.
Get new guides by emailOccasional emails. No spam. Unsubscribe anytime.