PERBOND
Bond it right — epoxy ratios, joint design, cure timing, and the adhesive calculators every workshop needs.
From estimating how much adhesive to buy and mixing two-part epoxy on-ratio to sizing a joint, adjusting cure time for temperature, and stretching a cartridge across a run, PerBond pairs free hands-on bonding calculators with practical guides and an illustrated museum. Prep well, bond once.
Adhesive & Bonding Calculators
Free tools for every bond — adhesive coverage calculator, epoxy mix ratio calculator, bond strength calculator, cure time calculator, coverage per cartridge, and lap joint designer.
Adhesive Coverage Calculator
Work out how much adhesive a job needs, from a bond area and glue-line thickness or a bead diameter and length, as a volume and approximate mass.
Epoxy Mix Ratio Calculator
Split a two-part epoxy batch into Part A and Part B by weight or volume at any ratio, with a warning when a big batch will shorten pot life.
Bond Strength Calculator
Estimate the load a lap-shear joint can carry from its area and the adhesive's shear strength, or the minimum area for a target load.
Cure Time Calculator
Adjust a base cure time for temperature, using the rule that cure roughly halves for every 10 °C rise and doubles for every 10 °C drop.
Coverage per Cartridge Calculator
Turn a cartridge or container volume into linear metres of bead at a chosen diameter, or the area it covers at a chosen spread thickness.
Lap Joint Designer
Size the overlap length a single-lap joint needs to carry a required load at a given adhesive shear strength and joint width.
Lap Joint Efficiency Calculator
Shear concentrates at the ends of a bonded overlap, so doubling the length does not double the strength — see how much of your overlap is working, and when to add width instead
The Museum
Wander an illustrated museum built entirely from Wikipedia and Wikimedia Commons — browse its collections, each in its own gallery, purely for the pleasure of looking and learning.
Tour the museum →From the Journal
Guides on choosing the right adhesive, prepping surfaces, mixing and curing epoxy, and designing stronger joints — practical reading to pair with the calculators above.
Overlap Length or Joint Width: Which Adds More Strength to a Bonded Joint?
Double the overlap of a bonded lap joint and the elastic model shows almost no gain; double the width and it doubles. A side-by-side comparison on 2 mm aluminium, with the caveats.
How Much Epoxy Do You Need for a Bonded Repair? From Glue Line to Weighed Batch
Work out the epoxy a bond needs from its area and glue-line thickness, add a sensible allowance, then split the batch into resin and hardener without going off-ratio.
How Many Metres of Bead Do You Get From a Cartridge of Adhesive or Sealant?
Bead length by cartridge size and nozzle cut, how to treat a rectangular sealant joint as an equivalent round bead, and how to work back from a job to a cartridge count.
How Long Does Epoxy Take to Cure at 10, 15, 20 and 30 °C?
A 24-hour epoxy takes about 48 hours at 15 °C and 67.88 at 10 °C. Cure-time tables by temperature, how to convert a data sheet quoted at 20 °C, and where the rule breaks down.
Epoxy Pot Life and Batch Size: Why a Big Mix Kicks Faster and How to Split It
Pot life is quoted for a small mass. Mix more and the batch heats itself, gels early and can smoke. How to split a job into batches that stay inside their working time.
Bonding Wood, Plastic or Painted Metal: When the Surface, Not the Glue, Sets the Strength
A multi-surface adhesive is only as strong as the weaker surface it is stuck to. Worked comparisons for bare steel, paint, wood and plastics, and why a stronger glue often changes nothing.
Keep Learning
Plain-language explainers on adhesive families, surface preparation, mix ratios and pot life, cure schedules, and joint design — everything you need to understand the numbers the tools produce and bond with more confidence.
Visit the Learn hub →