How to Mix Two-Part Epoxy by Weight or by Volume Without Going Off-Ratio
Two-part epoxy cures by a chemical reaction between a resin (Part A) and a hardener (Part B). Each molecule of one needs its partner from the other, so the two must be combined in a fixed proportion. Get it right and the mix cures hard right through. Get it wrong and the surplus of whichever part was overdosed has nothing to react with: it stays in the cured material as a soft, sticky or brittle weakness that no amount of waiting will fix. This guide shows how to read a mix ratio, how to split a batch with the Epoxy Mix Ratio Calculator, and the measuring mistakes that cause most failed cures.
Reading the ratio on the data sheet
A mix ratio is written as parts of A to parts of B, such as 1:1, 2:1, 5:1 or 100:30. Two things about it matter equally:
- The numbers. 100:30 means 100 parts of resin to 30 parts of hardener. It does not mean the hardener is 30 percent of the batch; it is 30 parts out of 130.
- The basis. Every ratio is either by weight or by volume, and the data sheet says which. Many products quote both, and the two sets of numbers are different.
The calculator has a "Ratio is by" selector for exactly this reason. Set it to match the figure you are reading, then measure the same way: grams on a scale for a weight ratio, millilitres in graduated cups or syringes for a volume ratio.
Splitting a batch
Each part is the batch total multiplied by its share of the ratio. For 300 g at 2:1, the calculator returns 200 g of resin and 100 g of hardener. The table shows a 60 g batch (small enough to stay under the calculator's exotherm warning) at the ratios you are most likely to meet:
| Ratio A:B | Part A (resin) | Part B (hardener) |
|---|---|---|
| 1:1 | 30 g | 30 g |
| 2:1 | 40 g | 20 g |
| 3:1 | 45 g | 15 g |
| 4:1 | 48 g | 12 g |
| 5:1 | 50 g | 10 g |
| 100:30 | 46.15 g | 13.85 g |
| 100:45 | 41.38 g | 18.62 g |
Notice how small the hardener figure becomes at the lopsided ratios. At 5:1 a 60 g batch needs only 10 g of hardener, and at 100:30 it needs 13.85 g. A slip of one gram on that 100:30 hardener is an error of 7.2 percent. The more lopsided the ratio, the more the accuracy of your scale matters, and the stronger the case for mixing a slightly larger batch than the job strictly needs.
Why 2:1 by volume is not 2:1 by weight
Resin and hardener do not weigh the same per millilitre. Resins are usually the denser of the two. Take a product with a 2:1 ratio by volume and, purely for illustration, a resin density of 1.15 g/ml and a hardener density of 0.98 g/ml. Two millilitres of resin weigh 2.3 g and one millilitre of hardener weighs 0.98 g, so the same recipe expressed by weight is about 2.35:1.
Now suppose you put that product on a scale and weigh it out at 2:1 because that is the number on the label. For a 90 g batch:
| Resin | Hardener | |
|---|---|---|
| Correct split by weight (2.3 : 0.98) | 63.11 g | 26.89 g |
| Weighed at 2:1 by mistake | 60 g | 30 g |
The mistaken batch has 3.11 g too much hardener, an overdose of 11.6 percent. Whether that is enough to spoil the cure depends on the product, but it is well outside the few percent of tolerance most data sheets allow. The densities here are made-up round figures to show the size of the effect. Never convert a ratio yourself from assumed densities: use the by-weight ratio the manufacturer prints, and if the sheet gives only a volume ratio, measure by volume.
Measuring by volume
For a volume ratio, the calculator works in millilitres. A 90 ml batch at 2:1 is 60 ml of resin and 30 ml of hardener. Three habits keep volume measuring honest:
- Use graduated cups or syringes, and read the level at eye height. Pencil marks on a tapered cup are not accurate: the same height holds more near the top than the bottom.
- Measure each part in its own container, then combine, scraping the thick resin out completely. What stays on the wall of the measuring cup is missing from the mix.
- If the product comes with calibrated pumps, use one full stroke of each. The pumps are sized to deliver the ratio stroke for stroke; counting five strokes of resin to one of hardener for a 5:1 product leaves the mix far short of hardener.
Cold resin is thick, clings to the cup and traps bubbles, which makes volume measuring less accurate still. Bringing both parts to room temperature before measuring helps. Weighing sidesteps the problem, which is why a by-weight ratio and a 0.1 g scale is the more repeatable method whenever the data sheet offers it.
Mixing: the other half of the ratio
A batch measured perfectly can still cure with soft patches if it is not mixed through, because locally the ratio is wrong wherever a streak of unmixed resin or hardener survives.
- Pour the smaller component into the larger, in a clean, flat-bottomed container with straight sides.
- Stir steadily for the time on the data sheet, commonly two to three minutes, with a flat-ended stick. Do not whip air in.
- Scrape the sides, the corners and the bottom of the container, and the stick itself, several times as you go. That is where unmixed material hides.
- For critical work, transfer the mix to a second clean cup and stir again. Anything left clinging to the first cup stays behind.
- Use it promptly. The clock started when the two parts met.
Things that do not work
- Adding extra hardener to speed the cure. It does not speed anything. It leaves unreacted hardener in the epoxy and weakens it. For a faster cure use a faster hardener or more warmth; the Cure Time Calculator shows what temperature does.
- Adding less hardener to gain working time. Same problem in reverse. For more time, use a slower hardener, a smaller batch or a cooler room.
- Swapping hardeners between brands or product lines. Ratios are specific to a resin and hardener pair.
- Thinning with solvent. It weakens the cured epoxy and brings a fire and vapour hazard with it.
Batch size and the exotherm warning
The calculator shows a warning when a batch is over about 100 g, because a large mass of mixed epoxy heats itself and shortens its own working time. For a volume batch it converts millilitres to grams at a typical 1.1 g/ml first: 90 ml counts as 99 g (warning shown: no), 120 ml as 132 g (warning shown: yes). The fix is several smaller batches or a shallow tray, covered in epoxy pot life and batch size. To work out how much to mix in the first place, see how much epoxy a bonded repair needs.
What the calculator does not cover
- It splits a total exactly at the ratio you type. It does not know your product, so it cannot catch a ratio entered on the wrong basis.
- It does not convert between weight and volume ratios. That needs the real densities of both parts, which only the manufacturer has.
- It gives no mixing time, pot life or tolerance. Those are on the technical data sheet.
- Its exotherm warning is a fixed threshold, not a prediction for your resin, cup or room temperature.
Safety
Epoxy resins and hardeners are skin sensitisers. The allergy builds with repeated contact, can appear after months or years of trouble-free use, and is permanent once it has developed. Wear nitrile gloves every time, replace them when they are contaminated, and keep sleeves down. Hardeners are often corrosive as well: wear eye protection, and treat a splash in the eye as an emergency, rinsing with water and following the first-aid section of the Safety Data Sheet (SDS).
Wash resin or hardener off skin with soap and water or a resin hand cleaner. Never clean your hands with solvent: it strips the skin's oils and carries the resin deeper. Mix and work with good ventilation, especially in warm conditions. A mixed batch generates heat, and a large one left in the cup can become hot enough to smoke and melt the container, so mix what you can use and never leave a full cup unattended.
Read the SDS and the technical data sheet for your product before opening it. The manufacturer's mix ratio, mixing method and cure schedule take priority over any calculator, this one included.