PERBOND
← The Journal
· The PerBond Team

How Many Metres of Bead Do You Get From a Cartridge of Adhesive or Sealant?

A 310 ml cartridge of adhesive or sealant lays 10.96 m of 6 mm round bead. Open the nozzle up to 10 mm and the same cartridge is empty after 3.95 m. The table below gives the length for the common cartridge and foil-pack sizes at seven bead diameters, and the rest of this guide shows how to use it for joints that are not round, how to work backwards from a job, and where the figures stop being reliable. Every number was produced by the Coverage per Cartridge Calculator, so you can reproduce any of them or enter your own sizes.

Bead length by cartridge size and diameter

Bead diameter290 ml310 ml400 ml600 ml
3 mm41.03 m43.86 m56.59 m84.88 m
4 mm23.08 m24.67 m31.83 m47.75 m
5 mm14.77 m15.79 m20.37 m30.56 m
6 mm10.26 m10.96 m14.15 m21.22 m
8 mm5.77 m6.17 m7.96 m11.94 m
10 mm3.69 m3.95 m5.09 m7.64 m
12 mm2.56 m2.74 m3.54 m5.31 m

These are geometric maximums: the volume of the cartridge divided by the cross-section of a round bead, with nothing left behind in the nozzle. Treat them as the most you could get, then take off an allowance (more on that below).

Why a slightly bigger nozzle cut costs so much

The cross-section of a round bead grows with the square of its diameter. Double the diameter and you use four times the material per metre, which the table shows directly: a 310 ml cartridge runs 15.79 m at 5 mm and 3.95 m at 10 mm, a ratio of 4 to 1. Even the step from 6 mm to 8 mm, which is hard to see by eye, uses 1.78 times as much.

The practical lesson is to cut the nozzle small and trim it back in stages. Cut it at an angle, lay a short test bead on scrap, measure it, and only then open it up if the data sheet's bead size calls for more. A nozzle cannot be cut smaller again.

Sealant joints are rectangles, not circles

A bead of adhesive on a flat surface starts out roughly round. A sealant gunned into a joint does not: it fills a slot of a given width and depth. The calculator works in round beads, but the conversion is simple, because what matters is the cross-sectional area. A joint 10 mm wide and 10 mm deep has a cross-section of 100 mm². A 10 mm round bead has only 78.5 mm², so entering "10 mm" for a 10 by 10 joint overstates the coverage by 27 percent.

Instead, enter the diameter of the round bead that has the same area as your joint. For a rectangle that is the square root of (4 × width × depth ÷ π). The table does it for four common joint sizes.

Joint (width × depth)Enter this bead diameter310 ml cartridge600 ml foil pack
6 × 6 mm6.8 mm8.6 m16.7 m
10 × 10 mm11.3 mm3.1 m6 m
12 × 8 mm11.1 mm3.2 m6.3 m
20 × 10 mm16 mm1.6 m3 m

A triangular fillet (the bead run into an internal corner, such as round a bath or a worktop upstand) has half the area of the rectangle that would enclose it, so a fillet with two 10 mm legs has a cross-section of 50 mm² and a 310 ml cartridge runs 6.2 m of it, twice as far as the 10 × 10 joint in the table. Movement joints in buildings also have rules about the ratio of sealant depth to width and need a backer rod; those come from the sealant maker's data sheet and are not something a coverage figure can tell you.

Working backwards: from the job to the cartridge count

Suppose you have 25 m of 8 mm bead to lay. You could read 6.17 m per 310 ml cartridge off the table and divide, or let the Adhesive Coverage Calculator do it in one step: choose "Round bead diameter + length", enter 8 mm and 25 m, and it returns 1,257 ml. That is 4.05 cartridges of 310 ml.

The answer is the awkward kind: a shade over four. Four cartridges leaves you short on paper before any waste, so the count is 5, and it stays at 5 with ten percent added. When the exact figure lands just above a whole number, buy the extra one. Running out part-way through a bead means a cold joint and a second trip.

Spreading instead of beading

If the product is trowelled or combed out, switch the calculator to "Area at a spread thickness". A 310 ml cartridge covers:

  • 0.31 m² at an average thickness of 1 mm
  • 0.155 m² at 2 mm
  • 0.103 m² at 3 mm

A 600 ml foil pack covers 0.3 m² at 2 mm. The thickness here is the average over the whole area. A notched trowel leaves ridges with bare strips between them, so the average is well below the notch depth, and a data sheet that quotes coverage in square metres per cartridge for a named trowel is a better guide than any assumed thickness.

How much to allow for waste

Real coverage is always below the geometric figure. The usual losses are:

  • The nozzle and the cartridge base. A few millilitres stay in every nozzle and behind the plunger. On a job that uses many cartridges, or needs a fresh nozzle each time, this adds up.
  • Starts, stops and tooling. Each time you release the trigger a little extra runs out, and tooling a sealant joint pushes material off the edges.
  • Uneven surfaces. A bead over a hollow or an open-textured surface is thicker than its nominal size.
  • Inconsistent speed. Slow down and the bead fattens. Because of the square law, a bead that averages 7 mm instead of 6 mm uses 36 percent more.

Ten percent is a reasonable allowance for steady beads on flat surfaces, and more on rough masonry or with a lot of short runs. The calculator does not add waste for you, so add it yourself and round up.

What the calculator does not cover

  • It assumes a perfectly round bead of constant diameter. Use the equal-area conversion above for joints and fillets.
  • It knows the volume printed on the cartridge, not how much actually comes out.
  • It does not know the product. Bead size, joint dimensions, open time and whether the adhesive suits your materials all come from the technical data sheet.
  • Two-part cartridges with a static mixing nozzle lose the contents of the mixer every time it is changed. Count nozzles as well as cartridges.

Safety

The contents of a cartridge are chemicals, whatever the label on the front calls them. Read the Safety Data Sheet (SDS) for the product before you start. Polyurethane adhesives and sealants contain isocyanates, which can cause asthma and skin allergy; two-part epoxies are skin sensitisers; solvent-based products give off flammable vapour; some silicones release acetic acid or other irritant vapours as they cure. Work with good ventilation, wear nitrile gloves and eye protection, and wash skin with soap and water, not solvent. Never point a nozzle at anyone, and release the pressure on the gun before you clear a blockage.

A coverage figure tells you how much to buy. It is not a measure of strength. A bead of adhesive is not a structural fixing, and anything load-bearing or overhead needs the fixings and design the manufacturer and a qualified engineer specify.

Quick reference

  • 6 mm bead: about 10.26 m from 290 ml, 10.96 m from 310 ml, 14.15 m from 400 ml, 21.22 m from 600 ml.
  • Doubling the bead diameter quarters the length.
  • For a rectangular joint, convert to the equal-area round bead before using the table.
  • Take about ten percent off for waste, then round the cartridge count up.

If the job is a subfloor or skirting, the construction adhesives guide works two examples through from room size to cartridge count.

Get new guides by emailOccasional emails. No spam. Unsubscribe anytime.