How Long Does Epoxy Take to Cure at 10, 15, 20 and 30 °C?
The cure time on an epoxy's data sheet is true at one temperature, normally somewhere between 20 and 25 °C. Workshops, garages and building sites are rarely that warm for half the year. As a rule of thumb, an epoxy's cure time doubles for every 10 °C drop in temperature and halves for every 10 °C rise, so a bond that is ready in 24 hours at 25 °C needs about 48 hours at 15 °C. This guide gives the figures across the working range, all from the Cure Time Calculator, and is clear about what that rule of thumb can and cannot tell you.
Cure time by temperature: the tables
The first table takes a time of 24 hours quoted at 25 °C. That could be time to handling strength, time before sanding or time before the next coat: whatever the data sheet attaches the 24 hours to. The second column is the multiplier, which you can apply to any other time quoted at 25 °C.
| Temperature | Multiplier | A 24 h step becomes | A 7-day full cure becomes |
|---|---|---|---|
| 5 °C | ×4 | 96 h | 28 days |
| 10 °C | ×2.828 | 67.88 h | 19.8 days |
| 15 °C | ×2 | 48 h | 14 days |
| 20 °C | ×1.414 | 33.94 h | 9.9 days |
| 25 °C | ×1 | 24 h | 7 days |
| 30 °C | ×0.707 | 16.97 h | 4.9 days |
| 35 °C | ×0.5 | 12 h | 3.5 days |
| 40 °C | ×0.354 | 8.49 h | 2.5 days |
The pattern to remember is the 10 °C steps: ×2 at 15 °C, ×4 at 5 °C, ×0.5 at 35 °C. A cool spring workshop at 15 °C doubles every time on the sheet. An unheated garage at 10 °C nearly triples it.
"Five-minute" epoxy is not five minutes either
Fast epoxies are affected in exactly the same proportion. A typical quick-set product gels in a few minutes but needs about an hour to reach handling strength at room temperature. Take that hour as the base:
- At 20 °C: 1.41 hours
- At 15 °C: 2 hours
- At 10 °C: 2.83 hours, which is 170 minutes
So the "quick" repair done in a cold garage and loaded after an hour was loaded at well under half its handling cure. Much of the reputation fast epoxies have for weak bonds comes from this.
Handling strength, sandable, full cure: which time do you need?
Data sheets usually give several times, and the temperature multiplier applies to all of them:
- Gel time or pot life. When the mix stops being workable.
- Handling or fixture time. When the joint can be unclamped and moved gently. It is nowhere near full strength.
- Time to sand or recoat. Hard enough to abrade without clogging the paper.
- Full cure. Design strength, chemical resistance and heat resistance. Commonly several days at room temperature.
Putting load on a joint at handling strength is the usual way a cold-weather bond fails. If the sheet says seven days to full cure at 25 °C, the table gives 14 days at 15 °C and 19.8 days at 10 °C.
Worked example: a garage at 12 °C
The data sheet says the epoxy can be sanded after 16 hours at 25 °C. The thermometer on the bench says 12 °C. In the calculator, enter 16 as the base cure time and 12 as the actual temperature. The result is 39.4 hours, a multiplier of 2.462. That is more than a day and a half: glue up on Saturday morning and it is late on Sunday night before it can be sanded, not Sunday morning.
If your data sheet quotes 20 °C or 23 °C
The calculator's base time is defined at 25 °C. Many European data sheets quote 20 °C or 23 °C instead. Entering a 20 °C time as if it were a 25 °C time makes every answer too long. To convert, use the calculator on itself: the sheet's temperature is 5 °C below the calculator's reference, so enter the sheet's time as the base and 30 °C (5 °C above the reference) as the temperature. For a product needing 24 hours at 20 °C that gives 16.97 hours, which is its equivalent time at 25 °C. Use 16.97 as the base from then on. At 10 °C that product comes out at 48 hours, double its 20 °C figure, as the 10 °C rule says it should.
Below 5 °C: the number becomes a lower bound
The calculator will not extrapolate below 5 °C. Enter 0 °C for the 24-hour example and it reports 96 hours, the 5 °C figure, and marks it as below the minimum (below minimum: yes). It does that on purpose. Many epoxies do not just slow down in the cold; below their minimum cure temperature the reaction effectively stops, and the epoxy can sit soft for weeks. Some never reach full properties afterwards even when warmed, and an amine blush (a waxy, sticky film on the surface) is common on epoxy cured cold and damp. So read the cold figure as "at least this long, and possibly never". The minimum application and cure temperature on the data sheet is a hard limit, not a suggestion. Special low-temperature hardeners exist for winter work.
Above 40 °C: faster, with conditions
The rule keeps halving as it gets warmer: 4.24 hours at 50 °C and 2.12 hours at 60 °C for the 24-hour example, and the calculator stops at 60 °C (enter 80 °C and it still reports 2.12 hours). Warmth is the legitimate way to speed a cure, and many epoxies reach higher strength and heat resistance with a warm post-cure. But it has conditions:
- Let the epoxy gel at room temperature first. Heating a fresh mix makes it runny, so it drains out of the joint, and shortens pot life sharply.
- Warm the whole assembly evenly with gentle heat, such as a warm room or an insulated tent with a small heater. A heat gun or a flame overheats the surface while the middle stays cold.
- Stay inside the temperature range the data sheet allows, for the epoxy and for the materials being bonded.
Measure the right temperature
The temperature that counts is the temperature of the glue line, not the air. A steel bracket on a concrete floor in winter can be several degrees colder than the room, and it will stay cold for hours after the heater goes on. Rest a thermometer on the part itself. Overnight lows matter as well: an epoxy applied at 18 °C in the afternoon spends most of its first day at whatever the workshop drops to at night. When in doubt, enter the lowest temperature the joint will see.
What the calculator does not cover
- It applies one rule of thumb, doubling per 10 °C, to every adhesive. Real products deviate from it, some considerably. If the data sheet has its own cure table for several temperatures, use that instead.
- It models temperature only. Moisture-curing adhesives (polyurethanes, silicones, MS polymers) and air-drying adhesives (PVA, contact adhesive) depend on humidity and airflow as well, and UV adhesives depend on light.
- It assumes a constant temperature. For a cold night after a warm day, use the lower figure.
- It does not model the heat a thick section of epoxy generates for itself, which speeds the cure in the middle of a large mass.
- It cannot tell you that a joint is strong enough to load. It only estimates when the adhesive has had the equivalent of its quoted time.
Safety
Epoxy that has not fully cured is still chemically active. Resins and hardeners are skin sensitisers, so wear nitrile gloves and eye protection when handling part-cured work, and wash with soap and water, never solvent. Do not sand epoxy before it has fully cured: the dust from part-cured epoxy can sensitise skin and lungs, and in a cold workshop "the next day" is often too soon. When you do sand, use dust extraction and a suitable dust mask.
Warming epoxy increases the vapour it gives off, so ventilate. Never use a naked flame, and never leave heaters unattended near solvents, rags or resin. A warm, thick mass of mixed epoxy can overheat by itself; see epoxy pot life and batch size.
Read the product's Safety Data Sheet (SDS) and technical data sheet. The manufacturer's cure schedule and minimum cure temperature always override this rule of thumb, and no cure-time estimate makes a joint safe to rely on for anything load-bearing or overhead.
Cold, damp conditions bring extra complications for waterproof adhesives and sealants that cure with moisture. Those are covered in how long a waterproof adhesive takes to cure in the cold.